濟南裝載機磨合期有什么特點？

磨合期是保證裝載機正常運轉、降低故障率、延長其使用壽命的重要環節，對裝載機磨合期的適用與保養應引起充分重視，在此之前我們應該了解磨合期有啊很么特點，以便更好的對裝載機進行維護。

1、操作失誤多
由于對機器的結構、性能的了解不夠，容易因操作失誤引起故障，甚至引起機械事故。
As the understanding of the structure and performance of the machine is not enough, susceptible to failures caused by operational errors, and even cause mechanical accident.
2、潤滑不良
由于新裝配的零部件的配合間隙較小，并且由于裝配等原因，很難保證配合間隙的均勻性，潤滑油不易在摩擦表面形成均勻的油膜以阻止磨損。從而降低潤滑效能，造成機件的早期異常磨損。嚴重時會造成精密配合的摩擦表面劃傷或咬合現象，導致故障的發生。
Since the new assembly parts with the gap is small, and due to assembly and other reasons, it is difficult to ensure uniformity with the gap, the lubricating oil on the friction surface is not easy to form a uniform film to prevent wear. Thereby reducing the lubrication performance, resulting in the early parts of abnormal wear. Will cause serious friction with precision surface scratches or bite phenomenon, leading to failure.　　
3、發生松動
新加工裝配的零部件，存在幾何形狀和配合尺寸的偏差，在使用初期，由于受到沖擊、振動等交變負荷，以及受熱、變形等因素的影響，加上磨損過快等原因，容易使原來緊固的零部件產生松動。
The new processing and assembly of components, there is a deviation geometry and with the size of the initial use, due to shock, vibration, etc. alternating load, and the effects of heat, deformation and other factors, coupled with excessive wear and other reasons, easy to make original loosening the fastening parts.
4、發生滲漏現象
由于機件的松動、振動合機器受熱的影響，機器的密封面以及管接頭登出會出現滲漏現象，部分鑄造、加工等缺陷在裝配調試時難于發現，但由于作業過程中的振動、沖擊作用，這種缺陷就被暴露出來，表現為漏油，因此，磨合期容易出現滲漏現象。
Since the sealing surface of the fitting parts and loose, vibration combined heat machine, the machine will be logged off leakage, part of the casting defects in the assembly and processing debugging difficult to find, but during the operation of the vibration, shock, role of this flaw is exposed, the performance of oil, therefore, prone to leakage of the run.　　
5、磨損速度快
由于新機器零部件加工、裝配和調整等因素的影響，其摩擦表面粗糙，配合面接觸面積小，表面的承壓狀況不均。機器在運行過程中，零件表面的凹凸部分相互嵌合摩擦，磨落下來的金屬碎屑又作為磨料繼續參與摩擦，更加速了零件配合表面的磨損。因此，磨合期內容易造成零部件的磨損，磨損速度快。這時，如果超負荷作業，則可能導致零部件的損壞，產生早期故障。
As the impact of the new machine parts processing, assembly and adjustment factors, the friction surface is rough, with surface contact area is small, uneven surface pressure situation. The machine during operation, some parts convex surface friction fitted into each other, grinding down to the metal debris and continue to participate as an abrasive friction, more accelerated wear parts with surfaces. Therefore, run-in period is likely to cause wear and tear parts, wear faster. At this time, if overload operation, it may cause damage to the components, resulting in premature failure.

濟南裝載機：http://www.ltjinhai.cn/